sl/slx-6rs-1/4/5 industrial ethernet switch sixnet networking series 6 port industrial ethernet ring switch solutions for your industrial networking challenges www.sixnet.com solutions for your industrial networking challenges www.sixnet.com 6 port industrial ethernet ring switch sl/slx-6rs-1/4/5 product datasheet the sl/slx-6rs is a 6 port industrial ethernet switch featuring sixnet?s real-time-ring? which provides very fast, fault-tolerant network redundancy and prioritized message delivery needed in critical real-time systems. these rings self-con ? gure and just run, without the complex con ? guration steps required by alternative solutions. this advanced technology delivers reliability and performance, saves you money, and makes your job easier. product highlights ? 6 ports including up to 2 ? ber optic ? super-fast, fault-tolerant ring redundancy ? pre-con? gured for true plug & play simplicity ? truly industrial hardened design ? slim case for din rail or direct panel mounting real-time fault-tolerant rings ? recovery time of 30 ms plus 5 ms per hop! ? ideal for deterministic systems and plcs ? real-time modbus over ethernet monitoring real-time traffic prioritization (qos) ? assure delivery of real-time data ? improve network utilization ? user settable priority assignments managed switch features ? at a lower cost ? user con? gurable port settings ? port mirroring for traf? c diagnostics ? message ? ltering to prevent broadcast storms trouble free operation ? ultra-reliable 1,000,000 + hours mtbf ? -40 to +85 c operating range (slx model) ? ul/csa (cul), ce and hazloc (zone 2) rated (pending) ? dual (redundant) power inputs ? industrial surge and spike protection ? self-test/alarm output contact t s rated sl slx sl slx 6 port industrial ethernet ring switch sl/slx-6rs-1/4/5 product datasheet the sl/slx-6rs is a 6 port industrial ethernet switch featuring sixnets real-time-ring? which provides very fast, fault-tolerant network redundancy and prioritized message delivery needed in critical real-time systems. these rings self-confgure and just run, without the complex confguration steps required by alternative solutions. this advanced technology delivers reliability and performance, saves you money, and makes your job easier. product highlights n 6 ports including up to 2 fber optic n super-fast, fault-tolerant ring redundancy n pre-confgured for true plug & play simplicity n truly industrial hardened design n slim case for din rail or direct panel mounting real-time fault-tolerant rings n recovery time of 30 ms plus 5 ms per hop! n ideal for deterministic systems and plcs n real-time modbus over ethernet monitoring real-time traffic prioritization (qos) n assure delivery of real-time data n improve network utilization n user settable priority assignments managed switch features C at a lower cost n user confgurable port settings n port mirroring for traffc diagnostics n message fltering to prevent broadcast storms trouble free operation n ultra-reliable 1,000,000 + hours mtbf n -40 to +85 c operating range (slx model) n ul/csa (cul), ce and hazloc (zone 2) rated n dual (redundant) power inputs n industrial surge and spike protection n self-test/alarm output contact solutions for your industrial networking challenges www.sixnet.com solutions for your industrial networking challenges www.sixnet.com 6 port industrial ethernet ring switch sl/slx-6rs-1/4/5 product datasheet the sl/slx-6rs is a 6 port industrial ethernet switch featuring sixnet?s real-time-ring? which provides very fast, fault-tolerant network redundancy and prioritized message delivery needed in critical real-time systems. these rings self-con ? gure and just run, without the complex con ? guration steps required by alternative solutions. this advanced technology delivers reliability and performance, saves you money, and makes your job easier. product highlights ? 6 ports including up to 2 ? ber optic ? super-fast, fault-tolerant ring redundancy ? pre-con? gured for true plug & play simplicity ? truly industrial hardened design ? slim case for din rail or direct panel mounting real-time fault-tolerant rings ? recovery time of 30 ms plus 5 ms per hop! ? ideal for deterministic systems and plcs ? real-time modbus over ethernet monitoring real-time traffic prioritization (qos) ? assure delivery of real-time data ? improve network utilization ? user settable priority assignments managed switch features ? at a lower cost ? user con? gurable port settings ? port mirroring for traf? c diagnostics ? message ? ltering to prevent broadcast storms trouble free operation ? ultra-reliable 1,000,000 + hours mtbf ? -40 to +85 c operating range (slx model) ? ul/csa (cul), ce and hazloc (zone 2) rated (pending) ? dual (redundant) power inputs ? industrial surge and spike protection ? self-test/alarm output contact t s rated sl slx sl slx 6 port industrial ethernet ring switch sl/slx-6rs-1/4/5 product datasheet the sl/slx-6rs is a 6 port industrial ethernet switch featuring sixnets real-time-ring? which provides very fast, fault-tolerant network redundancy and prioritized message delivery needed in critical real-time systems. these rings self-confgure and just run, without the complex confguration steps required by alternative solutions. this advanced technology delivers reliability and performance, saves you money, and makes your job easier. product highlights n 6 ports including up to 2 fber optic n super-fast, fault-tolerant ring redundancy n pre-confgured for true plug & play simplicity n truly industrial hardened design n slim case for din rail or direct panel mounting real-time fault-tolerant rings n recovery time of 30 ms plus 5 ms per hop! n ideal for deterministic systems and plcs n real-time modbus over ethernet monitoring real-time traffic prioritization (qos) n assure delivery of real-time data n improve network utilization n user settable priority assignments managed switch features C at a lower cost n user confgurable port settings n port mirroring for traffc diagnostics n message fltering to prevent broadcast storms trouble free operation n ultra-reliable 1,000,000 + hours mtbf n -40 to +85 c operating range (slx model) n ul/csa (cul), ce and hazloc (zone 2) rated n dual (redundant) power inputs n industrial surge and spike protection n self-test/alarm output contact solutions for your industrial networking challenges www.sixnet.com solutions for your industrial networking challenges www.sixnet.com 6 port industrial ethernet ring switch sl/slx-6rs-1/4/5 product datasheet the sl/slx-6rs is a 6 port industrial ethernet switch featuring sixnet?s real-time-ring? which provides very fast, fault-tolerant network redundancy and prioritized message delivery needed in critical real-time systems. these rings self-con ? gure and just run, without the complex con ? guration steps required by alternative solutions. this advanced technology delivers reliability and performance, saves you money, and makes your job easier. product highlights ? 6 ports including up to 2 ? ber optic ? super-fast, fault-tolerant ring redundancy ? pre-con? gured for true plug & play simplicity ? truly industrial hardened design ? slim case for din rail or direct panel mounting real-time fault-tolerant rings ? recovery time of 30 ms plus 5 ms per hop! ? ideal for deterministic systems and plcs ? real-time modbus over ethernet monitoring real-time traffic prioritization (qos) ? assure delivery of real-time data ? improve network utilization ? user settable priority assignments managed switch features ? at a lower cost ? user con? gurable port settings ? port mirroring for traf? c diagnostics ? message ? ltering to prevent broadcast storms trouble free operation ? ultra-reliable 1,000,000 + hours mtbf ? -40 to +85 c operating range (slx model) ? ul/csa (cul), ce and hazloc (zone 2) rated (pending) ? dual (redundant) power inputs ? industrial surge and spike protection ? self-test/alarm output contact t s rated sl slx sl slx 6 port industrial ethernet ring switch sl/slx-6rs-1/4/5 product datasheet the sl/slx-6rs is a 6 port industrial ethernet switch featuring sixnets real-time-ring? which provides very fast, fault-tolerant network redundancy and prioritized message delivery needed in critical real-time systems. these rings self-confgure and just run, without the complex confguration steps required by alternative solutions. this advanced technology delivers reliability and performance, saves you money, and makes your job easier. product highlights n 6 ports including up to 2 fber optic n super-fast, fault-tolerant ring redundancy n pre-confgured for true plug & play simplicity n truly industrial hardened design n slim case for din rail or direct panel mounting real-time fault-tolerant rings n recovery time of 30 ms plus 5 ms per hop! n ideal for deterministic systems and plcs n real-time modbus over ethernet monitoring real-time traffic prioritization (qos) n assure delivery of real-time data n improve network utilization n user settable priority assignments managed switch features C at a lower cost n user confgurable port settings n port mirroring for traffc diagnostics n message fltering to prevent broadcast storms trouble free operation n ultra-reliable 1,000,000 + hours mtbf n -40 to +85 c operating range (slx model) n ul/csa (cul), ce and hazloc (zone 2) rated n dual (redundant) power inputs n industrial surge and spike protection n self-test/alarm output contact
sl/slx-6rs-1/4/5 industrial ethernet switch specifications solutions for your industrial networking challenges www.sixnet.com sixnet technology park 331 ushers road ? ballston lake, ny 12019 ? usa 1.518.877.5173 ? fax 1.518.877.8346 ? sales@sixnet.com datasheet sl/slx-6rs-1/4/5 rev july 2, 2009 sl/slx-6rs-1/4/5 6 port industrial ethernet ring switch ethernet performance n 6 fast ethernet ports with up to 2 fber n managed, store & forward, wire-speed n all ieee 802.3 ethernet protocols supported n rj45 ports (shielded) 10/100basetx n rj45 port speed auto-negotiation n rj45 mdi/mdix auto-crossover n rj45 td and rd auto-polarity n fiber optional on port 5 and 6 n fiber optic port speed: 100 mbps n fiber typical specs (see separate datasheet for details) p multimode, 4 km, 1310 nm, 50-62.5/125 m p singlemode, 20 km, 1310 nm, 9-10/125 m p long haul, up to 120 km, 1550 nm, 9-10/125 m n typical latency (varies on load & settings) p @ 10 mbps: 16 us + frame time p @ 100 mbps: 5 us + frame time n full or half duplex operation confgurable per port n mac addresses supported 2048 n memory bandwidth 3.2 gbps n ethernet isolation 1500 vrms 1 minute ethernet compliance n ieee 802.3u (fast ethernet 100mbps for newer devices) n ieee 802.3 (10mbps ethernet supports legacy devices) n ieee 802.1p (priority queuing C qos, cos, tos/ds) n ieee 802.3x (full-duplex with flow control) real-time-ring? n link loss recovery: 30 ms plus 5 ms per hop n switches in a ring: <50 for best performance n multiple rings supported (confgurable) ok alarm output n indicates power & operational status n voltage same as switch input voltage n maximum current output 0.5 amp power input n redundant input terminals n reverse polarity protection n input power (typ. with all ports active) p 4 w (-1 model w/ no fber) p 6 w (-4/5 model w/ 2 fber) n power input voltage 10-30 vdc n transient protection 15,000 watts peak n spike protection 5,000 watts (10x for 10 us) all specifcations are subject to change. consult factory for latest info. ordering guide slx-6rs-1-d1 6 rj45 ports, metal case, wide temp . slx-6rs-4sc-d1 4 rj45 ports, 2 multimode sc, 4 km slx-6rs-4st-d1 4 rj45 ports, 2 multimode st, 4 km slx-6rs-5sc-d1 4 rj45 ports, 2 singlemode sc, 20 km slx-6rs-5st-d1 4 rj45 ports, 2 singlemode st, 20 km slx-6rs-5scl-d1 4 rj45 ports, 2 singlemode sc, 40+ km SLX-6RS-5STL-D1 4 rj45 ports, 2 singlemode st, 40+ km sl- w/ lexan case and limited temperature setup wizard free - windows confguration tool et-ps-024-02 power supply C ac to 24vdc, 2a sp-eth-2 dual port ethernet surge & lightning protector for 10/100 ports note: the suffx 1 means it is pre-confgured for 1 ring on ports 5 & 6. contact sixnet for other pre-confguration options. environmental n operating temperature: p slx: -40 to +85 c (cold startup at -40 c) p sl: -40 to +60 c n storage temperature -40 to +85 c n humidity (non-condensing) 5 to 95% rh (optional conformal coating is available) n vibration and shock C iec60068-2-6, -27 n maximum operating altitude: 30,000 ft. standards compliance n electrical safety C ul508 / csa c22.2/142; en61010-1, ce n emc C fcc part 15, ices-003; en61000-6-2/4, ce n hazardous locations C ansi/isa 12.12.01 / csa c22.2/213 (class i, div. 2); en60079-15 (zone 2, category 3), ce (atex) n maritime C designed for marine and offshore per abs n rohs and weee compliant physical n din rail or direct panel mounting n case C aluminum (slx) or lexan (sl) n ingress protection p sl models: ip30 p slx models: ip40 n weight C slx: 0.23 kg (8 oz.); sl: 0.17 kg (6 oz.) n dimensions C see mechanical diagram mechanical drawing solutions for your industrial networking challenges www.sixnet.com sixnet technology park 331 ushers road ? ballston lake, ny 12019 ? usa 1.518.877.5173 ? fax 1.518.877.8346 ? sales@sixnet.com atasheet slslx6rs145 re ly 2, 2009 sl/slx-6rs-1/4/5 6 port industrial ethernet ring switch ethernet performance n 6 fast ethernet ports with up to 2 fber n managed, store & forward, wire-speed n all ieee 802.3 ethernet protocols supported n rj45 ports (shielded) 10/100basetx n rj45 port speed auto-negotiation n rj45 mdi/mdix auto-crossover n rj45 td and rd auto-polarity n fiber optional on port 5 and 6 n fiber optic port speed: 100 mbps n fiber typical specs (see separate datasheet for details) p multimode, 4 km, 1310 nm, 50-62.5/125 m p singlemode, 20 km, 1310 nm, 9-10/125 m p long haul, up to 120 km, 1550 nm, 9-10/125 m n typical latency (varies on load & settings) p @ 10 mbps: 16 us + frame time p @ 100 mbps: 5 us + frame time n full or half duplex operation confgurable per port n mac addresses supported 2048 n memory bandwidth 3.2 gbps n ethernet isolation 1500 vrms 1 minute ethernet compliance n ieee 802.3u (fast ethernet 100mbps for newer devices) n ieee 802.3 (10mbps ethernet supports legacy devices) n ieee 802.1p (priority queuing C qos, cos, tos/ds) n ieee 802.3x (full-duplex with flow control) real-time-ring? n link loss recovery: 30 ms plus 5 ms per hop n switches in a ring: <50 for best performance n multiple rings supported (confgurable) ok alarm output n indicates power & operational status n voltage same as switch input voltage n maximum current output 0.5 amp power input n redundant input terminals n reverse polarity protection n input power (typ. with all ports active) p 4 w (-1 model w/ no fber) p 6 w (-4/5 model w/ 2 fber) n power input voltage 10-30 vdc n transient protection 15,000 watts peak n spike protection 5,000 watts (10x for 10 us) all specifcations are subject to change. consult factory for latest info. ordering guide slx-6rs-1-d1 6 rj45 ports, metal case, wide temp . slx-6rs-4sc-d1 4 rj45 ports, 2 multimode sc, 4 km slx-6rs-4st-d1 4 rj45 ports, 2 multimode st, 4 km slx-6rs-5sc-d1 4 rj45 ports, 2 singlemode sc, 20 km slx-6rs-5st-d1 4 rj45 ports, 2 singlemode st, 20 km slx-6rs-5scl-d1 4 rj45 ports, 2 singlemode sc, 40+ km SLX-6RS-5STL-D1 4 rj45 ports, 2 singlemode st, 40+ km sl- w/ lexan case and limited temperature setup wizard free - windows confguration tool et-ps-024-02 power supply C ac to 24vdc, 2a sp-eth-2 dual port ethernet surge & lightning protector for 10/100 ports note: the suffx 1 means it is pre-confgured for 1 ring on ports 5 & 6. contact sixnet for other pre-confguration options. environmental n operating temperature: p slx: -40 to +85 c (cold startup at -40 c) p sl: -40 to +60 c n storage temperature -40 to +85 c n humidity (non-condensing) 5 to 95% rh (optional conformal coating is available) n vibration and shock C iec60068-2-6, -27 n maximum operating altitude: 30,000 ft. standards compliance n electrical safety C ul508 / csa c22.2/142; en61010-1, ce n emc C fcc part 15, ices-003; en61000-6-2/4, ce n hazardous locations C ansi/isa 12.12.01 / csa c22.2/213 (class i, div. 2); en60079-15 (zone 2, category 3), ce (atex) n maritime C designed for marine and offshore per abs n rohs and weee compliant physical n din rail or direct panel mounting n case C aluminum (slx) or lexan (sl) n ingress protection p sl models: ip30 p slx models: ip40 n weight C slx: 0.23 kg (8 oz.); sl: 0.17 kg (6 oz.) n dimensions C see mechanical diagram mechanical drawing solutions for your industrial networking challenges www.sixnet.com sixnet technology park 331 ushers road ? ballston lake, ny 12019 ? usa 1.518.877.5173 ? fax 1.518.877.8346 ? sales@sixnet.com datasheet sl/slx-6rs-1/4/5 rev july 2, 2009 sl/slx-6rs-1/4/5 6 port industrial ethernet ring switch ethernet performance n 6 fast ethernet ports with up to 2 fber n managed, store & forward, wire-speed n all ieee 802.3 ethernet protocols supported n rj45 ports (shielded) 10/100basetx n rj45 port speed auto-negotiation n rj45 mdi/mdix auto-crossover n rj45 td and rd auto-polarity n fiber optional on port 5 and 6 n fiber optic port speed: 100 mbps n fiber typical specs (see separate datasheet for details) p multimode, 4 km, 1310 nm, 50-62.5/125 m p singlemode, 20 km, 1310 nm, 9-10/125 m p long haul, up to 120 km, 1550 nm, 9-10/125 m n typical latency (varies on load & settings) p @ 10 mbps: 16 us + frame time p @ 100 mbps: 5 us + frame time n full or half duplex operation confgurable per port n mac addresses supported 2048 n memory bandwidth 3.2 gbps n ethernet isolation 1500 vrms 1 minute ethernet compliance n ieee 802.3u (fast ethernet 100mbps for newer devices) n ieee 802.3 (10mbps ethernet supports legacy devices) n ieee 802.1p (priority queuing C qos, cos, tos/ds) n ieee 802.3x (full-duplex with flow control) real-time-ring? n link loss recovery: 30 ms plus 5 ms per hop n switches in a ring: <50 for best performance n multiple rings supported (confgurable) ok alarm output n indicates power & operational status n voltage same as switch input voltage n maximum current output 0.5 amp power input n redundant input terminals n reverse polarity protection n input power (typ. with all ports active) p 4 w (-1 model w/ no fber) p 6 w (-4/5 model w/ 2 fber) n power input voltage 10-30 vdc n transient protection 15,000 watts peak n spike protection 5,000 watts (10x for 10 us) all specifcations are subject to change. consult factory for latest info. ordering guide slx-6rs-1-d1 6 rj45 ports, metal case, wide temp . slx-6rs-4sc-d1 4 rj45 ports, 2 multimode sc, 4 km slx-6rs-4st-d1 4 rj45 ports, 2 multimode st, 4 km slx-6rs-5sc-d1 4 rj45 ports, 2 singlemode sc, 20 km slx-6rs-5st-d1 4 rj45 ports, 2 singlemode st, 20 km slx-6rs-5scl-d1 4 rj45 ports, 2 singlemode sc, 40+ km SLX-6RS-5STL-D1 4 rj45 ports, 2 singlemode st, 40+ km sl- w/ lexan case and limited temperature setup wizard free - windows confguration tool et-ps-024-02 power supply C ac to 24vdc, 2a sp-eth-2 dual port ethernet surge & lightning protector for 10/100 ports note: the suffx 1 means it is pre-confgured for 1 ring on ports 5 & 6. contact sixnet for other pre-confguration options. environmental n operating temperature: p slx: -40 to +85 c (cold startup at -40 c) p sl: -40 to +60 c n storage temperature -40 to +85 c n humidity (non-condensing) 5 to 95% rh (optional conformal coating is available) n vibration and shock C iec60068-2-6, -27 n maximum operating altitude: 30,000 ft. standards compliance n electrical safety C ul508 / csa c22.2/142; en61010-1, ce n emc C fcc part 15, ices-003; en61000-6-2/4, ce n hazardous locations C ansi/isa 12.12.01 / csa c22.2/213 (class i, div. 2); en60079-15 (zone 2, category 3), ce (atex) n maritime C designed for marine and offshore per abs n rohs and weee compliant physical n din rail or direct panel mounting n case C aluminum (slx) or lexan (sl) n ingress protection p sl models: ip30 p slx models: ip40 n weight C slx: 0.23 kg (8 oz.); sl: 0.17 kg (6 oz.) n dimensions C see mechanical diagram mechanical drawing solutions for your industrial networking challenges www.sixnet.com sixnet technology park 331 ushers road ? ballston lake, ny 12019 ? usa 1.518.877.5173 ? fax 1.518.877.8346 ? sales@sixnet.com datasheet sl/slx-6rs-1/4/5 rev july 2, 2009 sl/slx-6rs-1/4/5 6 port industrial ethernet ring switch ethernet performance n 6 fast ethernet ports with up to 2 fber n managed, store & forward, wire-speed n all ieee 802.3 ethernet protocols supported n rj45 ports (shielded) 10/100basetx n rj45 port speed auto-negotiation n rj45 mdi/mdix auto-crossover n rj45 td and rd auto-polarity n fiber optional on port 5 and 6 n fiber optic port speed: 100 mbps n fiber typical specs (see separate datasheet for details) p multimode, 4 km, 1310 nm, 50-62.5/125 m p singlemode, 20 km, 1310 nm, 9-10/125 m p long haul, up to 120 km, 1550 nm, 9-10/125 m n typical latency (varies on load & settings) p @ 10 mbps: 16 us + frame time p @ 100 mbps: 5 us + frame time n full or half duplex operation confgurable per port n mac addresses supported 2048 n memory bandwidth 3.2 gbps n ethernet isolation 1500 vrms 1 minute ethernet compliance n ieee 802.3u (fast ethernet 100mbps for newer devices) n ieee 802.3 (10mbps ethernet supports legacy devices) n ieee 802.1p (priority queuing C qos, cos, tos/ds) n ieee 802.3x (full-duplex with flow control) real-time-ring? n link loss recovery: 30 ms plus 5 ms per hop n switches in a ring: <50 for best performance n multiple rings supported (confgurable) ok alarm output n indicates power & operational status n voltage same as switch input voltage n maximum current output 0.5 amp power input n redundant input terminals n reverse polarity protection n input power (typ. with all ports active) p 4 w (-1 model w/ no fber) p 6 w (-4/5 model w/ 2 fber) n power input voltage 10-30 vdc n transient protection 15,000 watts peak n spike protection 5,000 watts (10x for 10 us) all specifcations are subject to change. consult factory for latest info. ordering guide slx-6rs-1-d1 6 rj45 ports, metal case, wide temp . slx-6rs-4sc-d1 4 rj45 ports, 2 multimode sc, 4 km slx-6rs-4st-d1 4 rj45 ports, 2 multimode st, 4 km slx-6rs-5sc-d1 4 rj45 ports, 2 singlemode sc, 20 km slx-6rs-5st-d1 4 rj45 ports, 2 singlemode st, 20 km slx-6rs-5scl-d1 4 rj45 ports, 2 singlemode sc, 40+ km SLX-6RS-5STL-D1 4 rj45 ports, 2 singlemode st, 40+ km sl- w/ lexan case and limited temperature setup wizard free - windows confguration tool et-ps-024-02 power supply C ac to 24vdc, 2a sp-eth-2 dual port ethernet surge & lightning protector for 10/100 ports note: the suffx 1 means it is pre-confgured for 1 ring on ports 5 & 6. contact sixnet for other pre-confguration options. environmental n operating temperature: p slx: -40 to +85 c (cold startup at -40 c) p sl: -40 to +60 c n storage temperature -40 to +85 c n humidity (non-condensing) 5 to 95% rh (optional conformal coating is available) n vibration and shock C iec60068-2-6, -27 n maximum operating altitude: 30,000 ft. standards compliance n electrical safety C ul508 / csa c22.2/142; en61010-1, ce n emc C fcc part 15, ices-003; en61000-6-2/4, ce n hazardous locations C ansi/isa 12.12.01 / csa c22.2/213 (class i, div. 2); en60079-15 (zone 2, category 3), ce (atex) n maritime C designed for marine and offshore per abs n rohs and weee compliant physical n din rail or direct panel mounting n case C aluminum (slx) or lexan (sl) n ingress protection p sl models: ip30 p slx models: ip40 n weight C slx: 0.23 kg (8 oz.); sl: 0.17 kg (6 oz.) n dimensions C see mechanical diagram mechanical drawing solutions for your industrial networking challenges www.sixnet.com sixnet technology park 331 ushers road ? ballston lake, ny 12019 ? usa 1.518.877.5173 ? fax 1.518.877.8346 ? sales@sixnet.com datasheet sl/slx-6rs-1/4/5 rev july 2, 2009 sl/slx-6rs-1/4/5 6 port industrial ethernet ring switch ethernet performance n 6 fast ethernet ports with up to 2 fber n managed, store & forward, wire-speed n all ieee 802.3 ethernet protocols supported n rj45 ports (shielded) 10/100basetx n rj45 port speed auto-negotiation n rj45 mdi/mdix auto-crossover n rj45 td and rd auto-polarity n fiber optional on port 5 and 6 n fiber optic port speed: 100 mbps n fiber typical specs (see separate datasheet for details) p multimode, 4 km, 1310 nm, 50-62.5/125 m p singlemode, 20 km, 1310 nm, 9-10/125 m p long haul, up to 120 km, 1550 nm, 9-10/125 m n typical latency (varies on load & settings) p @ 10 mbps: 16 us + frame time p @ 100 mbps: 5 us + frame time n full or half duplex operation confgurable per port n mac addresses supported 2048 n memory bandwidth 3.2 gbps n ethernet isolation 1500 vrms 1 minute ethernet compliance n ieee 802.3u (fast ethernet 100mbps for newer devices) n ieee 802.3 (10mbps ethernet supports legacy devices) n ieee 802.1p (priority queuing C qos, cos, tos/ds) n ieee 802.3x (full-duplex with flow control) real-time-ring? n link loss recovery: 30 ms plus 5 ms per hop n switches in a ring: <50 for best performance n multiple rings supported (confgurable) ok alarm output n indicates power & operational status n voltage same as switch input voltage n maximum current output 0.5 amp power input n redundant input terminals n reverse polarity protection n input power (typ. with all ports active) p 4 w (-1 model w/ no fber) p 6 w (-4/5 model w/ 2 fber) n power input voltage 10-30 vdc n transient protection 15,000 watts peak n spike protection 5,000 watts (10x for 10 us) all specifcations are subject to change. consult factory for latest info. ordering guide slx-6rs-1-d1 6 rj45 ports, metal case, wide temp . slx-6rs-4sc-d1 4 rj45 ports, 2 multimode sc, 4 km slx-6rs-4st-d1 4 rj45 ports, 2 multimode st, 4 km slx-6rs-5sc-d1 4 rj45 ports, 2 singlemode sc, 20 km slx-6rs-5st-d1 4 rj45 ports, 2 singlemode st, 20 km slx-6rs-5scl-d1 4 rj45 ports, 2 singlemode sc, 40+ km SLX-6RS-5STL-D1 4 rj45 ports, 2 singlemode st, 40+ km sl- w/ lexan case and limited temperature setup wizard free - windows confguration tool et-ps-024-02 power supply C ac to 24vdc, 2a sp-eth-2 dual port ethernet surge & lightning protector for 10/100 ports note: the suffx 1 means it is pre-confgured for 1 ring on ports 5 & 6. contact sixnet for other pre-confguration options. environmental n operating temperature: p slx: -40 to +85 c (cold startup at -40 c) p sl: -40 to +60 c n storage temperature -40 to +85 c n humidity (non-condensing) 5 to 95% rh (optional conformal coating is available) n vibration and shock C iec60068-2-6, -27 n maximum operating altitude: 30,000 ft. standards compliance n electrical safety C ul508 / csa c22.2/142; en61010-1, ce n emc C fcc part 15, ices-003; en61000-6-2/4, ce n hazardous locations C ansi/isa 12.12.01 / csa c22.2/213 (class i, div. 2); en60079-15 (zone 2, category 3), ce (atex) n maritime C designed for marine and offshore per abs n rohs and weee compliant physical n din rail or direct panel mounting n case C aluminum (slx) or lexan (sl) n ingress protection p sl models: ip30 p slx models: ip40 n weight C slx: 0.23 kg (8 oz.); sl: 0.17 kg (6 oz.) n dimensions C see mechanical diagram mechanical drawing www.redlion.net connect. monitor. control. americas sales@redlion.net asia-pacifc asia@redlion.net europe middle east africa europe@redlion.net +1 (717) 767-6511 as the global experts in communication, monitoring and control for industrial automation and networking, red lion has been delivering innovative solutions for over forty years. our automation, ethernet and cellular m2m technology enables companies worldwide to gain real-time data visibility that drives productivity. product brands include red lion, n-tron and sixnet. with headquarters in york, pennsylvania, the company has offces across the americas, asia-pacifc and europe. red lion is part of spectris plc, the productivity-enhancing instrumentation and controls company. for more information, please visit www.redlion.net . adld0329 091916 ? 2016 red lion controls, inc. all rights reserved. red lion, the red lion logo, n-tron and sixnet are registered trademarks of red lion controls, inc. all other company and product names are trademarks of their respective owners.
|
